Standards register
Pressure Equipment Directive, ASME and API codes, vessels, boilers, piping, flanges and gaskets, valves, hoses, chemical apparatus, welding, corrosion.
Themes concerned: Oil & Gas · Chemical & Petrochemical · Natural gas & LNG · Oil & fuels
236 standards and rules. Each line gives the designation, the subject and the publishing body. An underlined designation leads to its detailed sheet; the target, on the right, puts the standard at the centre of the map.
European legislation ASME codes API standards: relief, tanks, inspection Rotating equipment and heat exchangers Valves Tanks and storage Welding and non-destructive testing Corrosion and materials EC-BCI rules Switzerland Germany United States European and international standards Vessels, safety valves and boilers Chemical apparatus Metallic piping and tubes Flanges and gaskets Hoses Plastic piping and tanks European legislation 4 2014/68/EU Pressure Equipment Directive Also: PED, DESP, DGRL, 2014/68/UE EU 2014/68/EU Guidelines Guidelines on the application of the Pressure Equipment Directive EU 2014/29/EU Simple Pressure Vessels Directive EU 2010/35/EU Transportable Pressure Equipment Directive Also: TPED EU ASME codes 17 ASME BPVC Boiler and pressure vessel code ASME ASME BPVC Section I Power boilers ASME ASME BPVC Section II Materials ASME ASME BPVC Section V Nondestructive examination ASME ASME BPVC Section VIII Pressure vessels ASME ASME BPVC Section IX Welding, brazing and fusing qualifications ASME ASME B31 Code for pressure piping ASME ASME B31.1 Power piping ASME ASME B31.3 Process piping ASME ASME B31.4 Pipeline transportation systems for liquids and slurries ASME ASME B31.8 Gas transmission and distribution piping systems ASME ASME B16.5 Pipe flanges and flanged fittings, NPS 1/2 through NPS 24 ASME ASME B16.34 Valves: flanged, threaded and welding end ASME ASME B16.47 Large diameter steel flanges, NPS 26 through NPS 60 ASME ASME B36.10M Welded and seamless wrought steel pipe ASME ASME PCC-1 Guidelines for pressure boundary bolted flange joint assembly ASME ASME PCC-2 Repair of pressure equipment and piping ASME API standards: relief, tanks, inspection 12 Themes: Oil & fuels
API 520 Sizing, selection and installation of pressure-relieving devices API API 521 Pressure-relieving and depressuring systems Also: ISO 23251 API API 526 Flanged steel pressure-relief valves API API 2000 Venting atmospheric and low-pressure storage tanks Also: ISO 28300 API API 650 Welded tanks for oil storage API API 620 Design and construction of large, welded, low-pressure storage tanks API API 653 Tank inspection, repair, alteration and reconstruction API API 510 Pressure vessel inspection code API API 570 Piping inspection code API API 579-1 Fitness-for-service Also: ASME FFS-1 API API 580 Risk-based inspection API API 581 Risk-based inspection methodology API Rotating equipment and heat exchangers 8 API 610 Centrifugal pumps for petroleum, petrochemical and natural gas industries Also: ISO 13709 API ISO 5199 Technical specifications for centrifugal pumps, class II ISO ISO 2858 End-suction centrifugal pumps, rating 16 bar ISO ISO 9906 Rotodynamic pumps: hydraulic performance acceptance tests ISO EN 809 Pumps and pump units for liquids: common safety requirements CEN/CENELEC API 617 Axial and centrifugal compressors and expander-compressors API API 660 Shell-and-tube heat exchangers Also: ISO 16812 API TEMA Standards of the Tubular Exchanger Manufacturers Association TEMA Valves 14 EN 736 Valves: terminology CEN/CENELEC EN 19 Industrial valves: marking of metallic valves CEN/CENELEC EN 558 Industrial valves: face-to-face and centre-to-face dimensions CEN/CENELEC EN 593 Metallic butterfly valves CEN/CENELEC EN 12516 Industrial valves: shell design strength CEN/CENELEC ISO 5208 Industrial valves: pressure testing of metallic valves ISO ISO 15848 Industrial valves: fugitive emissions ISO ISO 10497 Testing of valves: fire type-testing requirements ISO API 598 Valve inspection and testing API API 6D Specification for pipeline and piping valves API DIN 3230 Technical delivery conditions for valves DIN EN 12266 Testing of metallic valves CEN/CENELEC EN 12266-1 Pressure tests, test procedures and acceptance criteria: mandatory requirements Also: DIN EN 12266-1 CEN/CENELEC EN 12266-2 Tests, test procedures and acceptance criteria: supplementary requirements Also: DIN EN 12266-2 CEN/CENELEC Tanks and storage 3 Themes: Oil & fuels
EN 14015 Site built, vertical, cylindrical, flat-bottomed, above ground, welded steel tanks CEN/CENELEC EN 13121 GRP tanks and vessels for use above ground CEN/CENELEC EN 12285 Workshop fabricated steel tanks CEN/CENELEC Welding and non-destructive testing 6 ISO 3834 Quality requirements for fusion welding of metallic materials ISO ISO 9606-1 Qualification testing of welders: steels ISO ISO 15614-1 Welding procedure test: arc and gas welding of steels and nickel ISO ISO 5817 Fusion-welded joints: quality levels for imperfections ISO ISO 9712 Non-destructive testing: qualification and certification of NDT personnel ISO ISO 17635 Non-destructive testing of welds: general rules for metallic materials ISO Corrosion and materials 12 ISO 12944 Corrosion protection of steel structures by protective paint systems ISO ISO 15156 Materials for use in hydrogen sulfide containing environments in oil and gas production Also: NACE MR0175 ISO ISO 21457 Materials selection and corrosion control for oil and gas production systems ISO DIN 17007 Material numbers DIN EN 10028-7 Flat products made of steels for pressure purposes: stainless steels Also: DIN EN 10028-7 CEN/CENELEC EN 10204 Metallic products: types of inspection documents Also: DIN EN 10204 CEN/CENELEC EN 1779 Non-destructive testing: leak testing Also: DIN EN 1779 CEN/CENELEC EN 12502 Protection of metallic materials against corrosion CEN/CENELEC EN 12502-1 General Also: DIN EN 12502-1 CEN/CENELEC EN 12502-3 Influencing factors for hot-dip galvanised ferrous materials Also: DIN EN 12502-3 CEN/CENELEC EN 14879-1 Organic coatings and linings for protection of industrial plants against corrosion caused by aggressive media Also: DIN EN 14879-1 CEN/CENELEC SN 37113 Paint and varnish industry: testing of coating materials Also: SNV 37113 SNV EC-BCI rules 33 Technical rules (TR) 9 TR EC BCI 150 Guide to the procurement and use of pressure vessels taking into account the Pressure Equipment Directive 2014/68/EU Also: TR BCI 150 EC-BCI TR EC BCI 151 Guide to implementing the Pressure Equipment Directive 2014/68/EU (PED) for piping Also: TR BCI 151 EC-BCI TR EC BCI 152 Technical requirements for pressure equipment Also: TR BCI 152 EC-BCI TR EC BCI 153 Quality assurance of welds on apparatus, vessels and piping Also: TR BCI 153 EC-BCI TR EC BCI 157 Guide to pressure relief systems Also: TR BCI 157 EC-BCI TR EC BCI 158 Thermal insulation and fire protection: piping, ventilation systems, cable penetrations Also: TR BCI 158 EC-BCI TR EC BCI 159 Thermal insulation of apparatus, thermal insulation with fire protection for storage tanks Also: TR BCI 159 EC-BCI TR EC BCI 160 Thermal insulation and fire protection of installations and plants Also: TR BCI 160 EC-BCI TR EC BCI 161 Guide to the calculation of explosion-pressure-shock-resistant tanks and vessels EC-BCI Basel standards (BN) 14 BN 5 Piping: stainless steel collar with welding end, DN 10 to 300 EC-BCI BN 76 Vessels: pressure-shock-resistant storage tanks, calculation of wall thicknesses withdrawn or superseded EC-BCI BN 80 Anti-rust primer coating of steel with two-component epoxy zinc-dust paint EC-BCI BN 81 Double-acting mechanical seals for agitated vessels withdrawn or superseded EC-BCI BN 83 Flat gaskets, PTFE-enveloped, inner-sealing EC-BCI BN 88 Identification of pipelines: marking, abbreviations, identification colours EC-BCI BN 93 Grinding and polishing of apparatus and parts made of stainless steel and nickel-base alloy EC-BCI BN 94 Pickling, passivation and electropolishing of piping, apparatus and parts made of stainless steel and nickel-base alloy EC-BCI BN 98 Vessels and apparatus, explosion-pressure-shock-resistant, for flammable liquids and dusts withdrawn or superseded EC-BCI BN 107 Cost estimation basis for piping EC-BCI BN 108 Corrosion protection of steel parts by paint coatings EC-BCI BN 109 Requirements for paint systems according to BN 108 EC-BCI BN 110 Storage tank in stainless steel, pressure-shock-resistant, vertical EC-BCI BN 111 Thermal insulation with fire protection for storage tanks withdrawn or superseded EC-BCI Switzerland 7 Druckgeräteverordnung Ordinance on the safety of pressure equipment CH Druckgeräteverwendungsverordnung Ordinance on the safety and health protection of workers using pressure equipment CH SVTI 721 Technical rules for industrial piping Also: TRIR SVTI SGK C1 Cathodic corrosion protection of pipelines SGK SGK C2 Corrosion protection of buried metallic installations SGK SGK C3 Corrosion protection against stray currents from direct-current installations SGK EKAS 6516 Pressure equipment Also: CFST 6516 EKAS Germany 11 VDI 2200 Tight flange connections: selection, calculation, design and assembly VDI VDI 2290 Emission control: characteristic values for tight flange connections VDI VDI 2532 Surface protection with organic materials: design and execution of metallic structures to be protected VDI AD 2000 Technical rules for pressure vessels VdTÜV AGI Q 103 Insulation work on industrial installations: electrical trace heating AGI AGI Q 104 Insulation work on industrial installations: trace heating systems with heat transfer fluid AGI AGI Q 151 Corrosion protection under insulation AGI BG RCI T002 Hose assemblies BG RCI BG RCI T039 Pressure tests of pressure vessels and piping BG RCI DVS 2205-1 Design calculations for containers and apparatus made of thermoplastics: characteristic values DVS DVS 2210-1 Industrial piping made of thermoplastics: design and execution of above-ground pipe systems DVS United States 1 API 682 Shaft sealing systems for centrifugal and rotary pumps API European and international standards 1 ISO 12162 Thermoplastics materials for pressure pipes and fittings: classification, designation and design coefficient ISO Vessels, safety valves and boilers 18 EN 13445-2 Unfired pressure vessels: materials Also: DIN EN 13445-2 CEN/CENELEC EN 764-7 Pressure equipment: safety systems for unfired pressure equipment Also: SN EN 764-7 CEN/CENELEC ISO 4126 Safety devices for protection against excessive pressure ISO ISO 4126-1 Safety valves Also: DIN EN ISO 4126-1 ISO ISO 4126-2 Bursting disc safety devices Also: DIN EN ISO 4126-2 ISO ISO 4126-3 Safety valves and bursting disc safety devices in combination Also: DIN EN ISO 4126-3 ISO ISO 4126-6 Application, selection and installation of bursting disc safety devices Also: DIN EN ISO 4126-6 ISO ISO 4126-7 Common data Also: DIN EN ISO 4126-7 ISO ISO 4126-10 Sizing of safety valves for gas/liquid two-phase flow Also: DIN EN ISO 4126-10 ISO SN 132150 Valves for process plants: spring-loaded safety valve PN 16 SNV SN 132151 Valves for process plants: spring-loaded safety valve PN 16, with bellows SNV DIN 477 Gas cylinder valves DIN EN 12952-7 Water-tube boilers and auxiliary installations: requirements for equipment for the boiler Also: DIN EN 12952-7 CEN/CENELEC EN 12953 Shell boilers CEN/CENELEC EN 12953-6 Requirements for equipment for the boiler Also: DIN EN 12953-6 CEN/CENELEC EN 12953-7 Requirements for firing systems for liquid and gaseous fuels for the boiler Also: DIN EN 12953-7 CEN/CENELEC EN 12953-10 Requirements for feedwater and boiler water quality Also: DIN EN 12953-10 CEN/CENELEC EN 12953-11 Acceptance tests Also: DIN EN 12953-11 CEN/CENELEC Chemical apparatus 48 Vessels, columns and apparatus components 15 DIN 28005-1 General tolerances for vessels: vessels in general DIN DIN 28007 General tolerances for columns DIN DIN 28011 Dished ends, Klöpper (torispherical) shape DIN DIN 28013 Dished ends, Korbbogen (semi-ellipsoidal) shape DIN DIN 28020 Horizontal pressure vessels DIN DIN 28082-1 Skirt supports DIN DIN 28084 Support rings DIN DIN 28105 Chemical apparatus: vessels with two dished ends DIN DIN 28122 Chemical apparatus DIN DIN 28124 Manhole closures DIN DIN 28124-3 For stainless steel pressure vessels DIN DIN 28124-4 Swivel devices DIN DIN 28128 Half-pipe coils for chemical apparatus DIN DIN 28140 Connections for outlet valves on vessels DIN Agitated vessels and agitators 13 DIN 28006 General tolerances for agitated vessels DIN DIN 28130 Agitated vessels with agitator unit DIN DIN 28131 Agitators for agitated vessels DIN DIN 28132 Agitator units: agitator shaft diameters DIN DIN 28135 Axial thrust discs for flange couplings on vertical agitator shafts DIN DIN 28136 Agitated vessels DIN DIN 28137 Agitator unit flanges DIN DIN 28138 Mechanical seals for agitator shafts DIN DIN 28154 Shaft ends for agitators made of unalloyed and stainless steel DIN DIN 28156 Shaft ends for agitators made of unalloyed and stainless steel, for stuffing boxes: dimensions DIN DIN 28160 Support rings for agitated vessels made of unalloyed and stainless steel DIN DIN 28161 Agitator drive requirements: speed, direction of rotation, bearings, running accuracy, removal space for mechanical seal DIN DIN 28162 Agitator unit lanterns DIN Glass-lined apparatus 10 DIN 28145 Welded-on parts for glass-lined steel agitated vessels DIN DIN 28146 Glass-lined steel baffles for agitated vessels DIN DIN 28148 PTFE-envelope gaskets for glass-lined steel agitated vessels DIN DIN 28150 Split loose flanges for glass-lined welding collars DIN DIN 28151 Jacket nozzles for glass-lined steel agitated vessels DIN DIN 28152 Clamping screws for glass-lined apparatus DIN DIN 28153 Closure covers for glass-lined steel apparatus DIN DIN 28157 One-piece impeller agitators, glass-lined steel DIN DIN 28158 One-piece anchor agitators, glass-lined steel DIN DIN 28159 Shaft ends for one-piece glass-lined steel agitators DIN SN 131450 Apparatus for process plants: glass-lined apparatus SNV SN 131450-1 Glass-lined steel apparatus and parts Also: SN 131450/1 SNV SN 131450-3 Thermal shock resistance on the apparatus, quality requirements Also: SN 131450/3 SNV Shell-and-tube heat exchangers 3 DIN 28008 General tolerances for shell-and-tube heat exchangers DIN DIN 28180 Seamless steel tubes for shell-and-tube heat exchangers DIN DIN 28182 Tube pitches and tube joints for expanded or welded-in steel tubes DIN DIN 7080 Circular sight glass plates for pressure service up to 300 °C, without low-temperature limit DIN DIN 7081 Long sight glass plates for pressure service up to 243 °C / 300 °C, without low-temperature limit DIN DIN 8902 Circular sight glass plates for pressure service up to 150 °C, without low-temperature limit DIN DIN 168-1 Knuckle threads, preferably for glass containers DIN Flanges and gaskets 6 EN 1092-1 Flanges and their joints: circular flanges for pipes, valves, fittings and accessories, steel flanges Also: DIN EN 1092-1 CEN/CENELEC EN 1591-1 Flanges and their joints: calculation Also: DIN EN 1591-1 CEN/CENELEC EN 13555 Flanges and their joints: gasket parameters and test procedures Also: DIN EN 13555 CEN/CENELEC DIN 28090 Gaskets: gasket characteristic values and test procedures DIN DIN 2695 Membrane sealing rings and membrane weld gaskets for flanged joints DIN DIN 2696 Sealing lenses and lens gaskets DIN Hoses 8 DIN 2825 Elastomer hose assemblies for steam and hot water DIN EN 12115 Rubber and plastics hoses and hose assemblies for liquid and gaseous chemicals Also: DIN EN 12115 CEN/CENELEC EN 853 Rubber hoses and hose assemblies: wire braid reinforced hydraulic hoses Also: DIN EN 853 CEN/CENELEC ISO 10380 Pipework: corrugated metal hoses and hose assemblies Also: DIN EN ISO 10380 ISO ISO 6134 Rubber hoses and hose assemblies for saturated steam Also: DIN EN ISO 6134 ISO ISO 2398 Rubber hoses, textile-reinforced, for compressed air Also: DIN EN ISO 2398 ISO ISO 5774 Plastics hoses: textile-reinforced types for compressed-air applications Also: DIN EN ISO 5774 ISO ISO 3821 Gas welding equipment: rubber hoses for welding, cutting and allied processes Also: DIN EN ISO 3821 ISO Plastic piping and tanks 10 DIN 8074 Polyethylene (PE 80, PE 100) pipes: dimensions DIN DIN 8075 Polyethylene (PE 80, PE 100) pipes: general quality requirements, testing DIN DIN 8077 Polypropylene (PP-H, PP-B, PP-R, PP-RCT) pipes: dimensions DIN DIN 8078 Polypropylene (PP-H, PP-B, PP-R, PP-RCT) pipes: general quality requirements, testing DIN DIN 16964-1 Wound glass-fibre reinforced plastic (GRP) pipes based on unsaturated polyester resins (UP resin) DIN DIN 16965 Wound glass-fibre reinforced plastic (GRP) pipes based on unsaturated polyester resins, without lining DIN DIBt Medienliste Media list for plastic tanks, collecting devices and pipes DIBt ISO 2078 Plastics: textile glass yarns Also: SN ISO 2078 ISO ISO 2558 Plastics: textile glass chopped-strand mats for reinforcement of plastics Also: SN ISO 2558 ISO ISO 2578 Plastics: determination of time-temperature limits after prolonged exposure to heat Also: SN ISO 2578 ISO All domains Process safety 